pdf-icon

CONTENTS

M5CameraF New

SKU:U037

Preview
Preview
Preview
Preview
Preview
Preview
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail

Description

M5CameraF is a development board for image recognition. It features an ESP32(4M Flash + 520K RAM) chip and 2-Megapixel camera (OV2640).

The module offers plenty of storage with an extra 4 Mbyte PSRAM. It also supports image transmission via Wi-Fi and debugging through USB Type-C port.

The hardware comes with preloaded software, programmed by ESP-IDF. It is an application to run Wi-Fi camera. The output image resolution is 600*800, since it's 2MP camera, you sure can optimize the software to output a better resolution image.

what this software can do?

  • Power the board via USB type-C or GROVE
  • Use your phone to Wi-Fi scan an AP name start with 'm5stack-' and click to connect this AP.
  • Open up web browser on your phone and visit 192.168.4.1
  • Then here comes the picture. Video is about 5-6 frames per seconds. not super fast.

Product Features

  • CP2104 USB-to-TTL converter
  • ESP32-WROVER (PCB Antenna)
  • WIFI image transmission
  • OV2640 sensor
  • Camera Field of View : 150 degree

Include

  • 1x M5CameraF
  • 1x LEGO Adapter
  • 1x Wall/1515
  • 1x Type-C USB(20cm)

Specification

Resources Parameter
Flash 4M
RAM 4MB
Image Sensor OV2640
Maximum resolution 2M pixel
Output format YUV(422/420)/YCbCr422,RGB565/555,8-bit compressed data,8-/10-bit Raw RGB data
FOV 150°
CCD Size 1/4 inch
Net weight 17g
Gross weight 41g
Product Size 24*48*19mm
Package Size 75*45*30mm

EasyLoader

download EasyLoader

What is EasyLoader?
1.EasyLoader is a simple and fast program burner. Every product page in EasyLoader provides a product-related case program. It can be burned to the master through simple steps, and a series of function verification can be performed. .
  1. After downloading the software, double-click to run the application, connect the M5 device to the computer through the data cable, select the port parameters, click "Burn" to start burning. (For M5StickC burning, please Set the baud rate to 750000 or 115200)

PinMap

Camera Interface PinMap

*Interface* *Camera Pin* *M5CameraF*
SCCB Clock SIOC IO23
SCCB Data SIOD IO22
System Clock XCLK IO27
Vertical Sync VSYNC IO25
Horizontal Reference HREF IO26
Pixel Clock PCLK IO21
Pixel Data Bit 0 D2 IO32
Pixel Data Bit 1 D3 IO35
Pixel Data Bit 2 D4 IO34
Pixel Data Bit 3 D5 IO5
Pixel Data Bit 4 D6 IO39
Pixel Data Bit 5 D7 IO18
Pixel Data Bit 6 D8 IO36
Pixel Data Bit 7 D9 IO19
Camera Reset RESET IO15
Camera Power Down PWDN *see Note 1*
Power Supply 3.3V 3V3 3V3
Ground GND GND

GROVE Interface

*Grove* *M5CameraF*
SCL IO13
SDA IO4
5V 5V
GND GND

LED Interface

LED *M5CameraF*
LED_Pin IO14

NOTE:

  1. Camera Power Down pin does not need to be connected to ESP32 GPIO. Instead it may be pulled down to ground with 10 kOhm resistor.

View M5 camera series/product differences

Schematic

Power circuit

Chip peripheral circuit

USB to serial port part of the circuit

Example

Firmware

Arduino

Code

Source Code