ESP32CAM-PSRAM
Description
ESP32CAM-PSRAM is a development board for image recognition. It features an ESP32(4MB Flash + 520KB RAM + 4MB PSRAM) chip and 2-Megapixel camera (OV2640).
The module offers plenty of storage with an extra 4 Mbyte PSRAM. It also supports image transmission via Wi-Fi and debugging through USB Type-C port.
The hardware comes with preloaded software, programmed by ESP-IDF. It is an application to run Wi-Fi camera. The output image resolution is 600*800, since it's 2MP camera, you sure can optimize the software to output a better resolution image.
Using processes:
- Power the board via USB type-C or GROVE
- Use your phone to Wi-Fi scan an AP name start with 'm5stack-' and click to connect this AP.
- Open up web browser on your phone and visit 192.168.4.1
- Then here comes the picture. Video is about 5-6 frames per seconds. not super fast.
Features
- CP2104 USB-to-TTL converter
- ESP32-WROVER (PCB Antenna)
- WIFI image transmission
- OV2640 Camera
- Camera Field of View : 150 degree
Includes
- 1 x ESP32CAM-PSRAM（Without Casing）
- 1 x Camera (OV2640)
Applications
- DIY
- Time-lapse photography
- IoT monitoring
Specification
| Resources | Parameters |
|---|---|
| Flash/RAM | 4MB/500K |
| PSRAM | 4M PSRAM |
| Image Sensor | OV2640 |
| Maximum resolution | 2M pixel |
| Output format | YUV(422/420)/YCbCr422,RGB565/555,8-bit compressed data,8-/10-bit Raw RGB data |
| FOV | 150° |
| CCD Size | 1/4 inch |
| Product Size | 47*20*10mm |
| Package Size | 136* 92* 13mm |
| Product Weight | 9.4g |
| Package Weight | 11.8g |
EasyLoader
EasyLoader is a simple and fast program burner. Every product page in EasyLoader provides a product-related case program. It can be burned to the master through simple steps, and a series of function verification can be performed. .
PinMap
Camera Interface PinMap
| *Interface* | *Camera Pin* | *ESP32CAM-PSRAM* |
|---|---|---|
| SCCB Clock | SIOC | IO23 |
| SCCB Data | SIOD | IO22 |
| System Clock | XCLK | IO27 |
| Vertical Sync | VSYNC | IO25 |
| Horizontal Reference | HREF | IO26 |
| Pixel Clock | PCLK | IO21 |
| Pixel Data Bit 0 | D2 | IO32 |
| Pixel Data Bit 1 | D3 | IO35 |
| Pixel Data Bit 2 | D4 | IO34 |
| Pixel Data Bit 3 | D5 | IO5 |
| Pixel Data Bit 4 | D6 | IO39 |
| Pixel Data Bit 5 | D7 | IO18 |
| Pixel Data Bit 6 | D8 | IO36 |
| Pixel Data Bit 7 | D9 | IO19 |
| Camera Reset | RESET | IO15 |
| Camera Power Down | PWDN | *see Note 1* |
| Power Supply 3.3V | 3V3 | 3V3 |
| Ground | GND | GND |
GROVE Interface
| *Grove* | *ESP32CAM-PSRAM* |
|---|---|
| SCL | IO13 |
| SDA | IO4 |
| 5V | 5V |
| GND | GND |
LED Interface
| LED | *ESP32CAM-PSRAM* |
|---|---|
| LED_Pin | IO14 |
NOTE:
View ESP32CAM-PSRAM series/product differences
Related Link
Schematic
Power circuit
Chip peripheral circuit
USB to serial port part of the circuit
Module Size
Example
Firmware
Arduino
Code
** Serial communication-M5Core **（The serial communication routine is the communication between the camera and the M5Core.）