Current Product Don't Have Test Firmware
Note: pls, use PC chrome/edge browser, if can't connect, refresh the webpage.
1. Click connect button
2. After connected successfully, pick a firmware
3. Click the burn button
4. After burning successfully, Unplug the device and restart.
ATOM HUB PROTO is a DIY proto board module designed for use with the ATOM series. Users can build circuits or connect peripherals according to their own needs to satisfy the functions and requirements of specific scenarios. Considering the various possibilities of user connection, ATOM HUB PROTO provides a wealth of interfaces, including VH3.96 interface, DC-5V power interface, grove interface, and all kinds of openings are reserved on the shell to facilitate user wiring。A variety of mounting holes are designed on the back of the fuselage, which not only support the traditional hanging holes and screw fixing holes, but also support the fixation of slide rail clamps.Built in proto circuit board, main circuit space layout 45x35x20mm.With atomhub, you can make your own hardware devices at will, such as connecting batteries by yourself, or integrating micro air pump + air pressure sensor to make a blood pressure meter, or even building a positioning and tracking system with GPS + NB-IoT module.
|External port||1x VH-3.96 4P 6x VH-3.96 3P 1x DC5V Input 1x GROVE|
|Package Size||104 x 77 x 35mm|
|Case material||Plastic ( PC )|
Depending on your use case you can design the circuit or prototype, soldering the corresponding components,through the vh-3.96 interface to connect external electrical equipment.You can also choose to purchase round waterproof connector connecting cable by yourself.
If you need to supply power through an external power supply, you can choose to supply power directly to ATOM through USB, or solder the DC 5V connector and connect the positive and negative poles to the corresponding pins of the ATOM. If the input voltage is higher than 5V, you need to build your own voltage step-down circuit.If you need to use the GROVE port, connect the pad breakpoint corresponding to the pin number you decide to use.
A remote control circuit is built in ATOM HUB PROTO by using the step-down circuit and relay. The control pin of the relay is GPIO21, which is powered by an external power supply. It is connected to Apple's Homekit application through Wi-Fi for remote control. Open the Homekit for manual connection. The default password is 11111111. Use the Siri voice remote control or manual button for remote control.
Execute the following statement in Setup() of the Arduino program
When M5Core2 is stacked with other M5 modules, you need to remove the battery base of Core2, which does not support module stacking.
Reason and solution: The power supply current of the port is insufficient, which can cause the device to not enter the download mode normally. You can try to connect a capacitor (>0.1uF) between the RST pin and the GND pin, or when uploading the program, set the G0 Short-circuit to GND, so that G0 can be set to a low level state normally
Add the header file #include <driver/adc.h> and the function adc_power_acquire(); in the Arduino program
The battery life of the controller is affected by various factors such as battery capacity, operating status, and load, so there is no fixed value. Reducing the load and adopting a sleep strategy can effectively increase the battery life.
Support multiple stacks, the total capacity of the batteries in parallel increases, and the voltage remains unchanged. However, since the discharge of each battery is not balanced during use, there is a voltage difference between the batteries, which may cause the battery to charge backwards. .(will lose part of the battery capacity)
ESP32 module currently does not support WiFi in 5G band, only 2.4G.
Confirm whether the TX/RX pin on the TTL side of the pin is correct, try to add two 120Ω terminal resistors at the beginning and end of the device line to reduce signal reflection interference
Click the link below to view the product comparison table
Rotate the lens to adjust the focal length within a certain range
Use esptool to read the flash content of esp32 and export the bin file. Refer to the detailed operation
Restart the Arduino IDE, the computer uses the mobile AP mobile network to download.
Refer to the Github link below, use arduino-esp32fs-plugin for file upload
Check if the COM of the corresponding device is selected and if the M5Burner is the latest version
UIFlow users can switch the Label font to Unicode, Arduino users can use the Chinese font library provided in the M5GFX driver library
Confirm whether the SD card format is FAT32, and no partitions exist.
You can refer to the following link for other ESP32 users to share the case program
STAMP C3U enters program download mode operation: 1. Long press the center button (G9) of STAMP C3U when the power is off. 2. Connect to the computer, after the port is successfully identified, program burning.
By default, USB CDC is not enabled, the serial port output started by C3U will be output through the default pins (G20, G21) of UART0. If you want to output through USB, please use the IDE to output Its USB CDC option is enabled. (Arduino users can enable it through Tools->USB CDC on Boot-Enabled. For IDF users, please refer to the ESP IDF official documentation.)
Refer to the UIFlow documentation of the corresponding device to check whether the device has entered the USB programming mode.
Describe the problems encountered in detail. Screenshots of the programs involved or files can be added as attachments and sent to M5Stack's official after-sales email