Current Product Don't Have Test Firmware
Note: pls, use PC chrome/edge browser, if can't connect, refresh the webpage.
1. Click connect button
2. After connected successfully, pick a firmware
3. Click the burn button
4. After burning successfully, Unplug the device and restart.
CardKB HAT is an implementation of a full-featured QWERTY keyboard tailored as a HAT for the M5StickC. Consider that you want to make some cool stuff that require interaction through typing on a keyboard. But M5StickC itself just has 2 buttons. So, here comes the flexible and yet powerful “CardKB HAT” to solve the issue.
The CardKB HAT also offers support for several button combinations (Shift+Key, Fn+Key) adding virtually many different keys. This comes with an RGB LED to indicate the keyboard state. I2C address is 0x5F.
This product is EOL now, we've released the updated version CardKB Mini Keyboard Programmable Unit (MEGA328P) which is fully compatible with this product.
Resources | Parameter |
---|---|
Communication protocol | I2C:0x5F |
Net weight | 17g |
Gross weight | 21g |
Product Size | 84.6*54.26.5mm |
Package Size | 115*96*40mm |
Button combination description:
Single button is pressed,once pressed button the led flashing blue.keyboard will output the first (normal) key value in its lower case. E.g. if "Q" is pressed, keyboard will output "q"(lower case).
Shift+Key, After pressing the Shift key, led flashing red,if a letter button is pressed, it'll output the letter in its upper case or the second value. E.g. if "Shift" is pressed once, then "Q" is pressed, the keyboard will output "Q". If "Shift" is double clicked, then the keyboard will lock this function and all the letter keys pressed will give output in CAPITALS.
Fn+Key(custom function key combination), led flashing green,keyboard will output the third key value, which you can customize based on the requirement.
Double-click Shift or fn to lock Shift(red always on) or Fn(green always on) and output the second value or third value multiple times.
After downloading the software, double-click to run the application, connect the M5 device to the computer through the data cable, select the port parameters, click "Burn" to burn the program (For M5StickC, set the baud rate to 115200 or 750000)
ATMega328 ISPDownload interface Pin foot definition
/*--------------------------------------------------------------------------------------------------*/
| KEYBOARD REG | 0x5F
| ------------------------------------------------------------------------------------------------
| keyboard_value_reg[0] | R | KEYBOARD VALUE
/*----------------------------------------------------------------------------------------------------
Execute the following statement in Setup() of the Arduino program
When M5Core2 is stacked with other M5 modules, you need to remove the battery base of Core2, which does not support module stacking.
Reason and solution: The power supply current of the port is insufficient, which can cause the device to not enter the download mode normally. You can try to connect a capacitor (>0.1uF) between the RST pin and the GND pin, or when uploading the program, set the G0 Short-circuit to GND, so that G0 can be set to a low level state normally
Add the header file #include <driver/adc.h> and the function adc_power_acquire(); in the Arduino program
The battery life of the controller is affected by various factors such as battery capacity, operating status, and load, so there is no fixed value. Reducing the load and adopting a sleep strategy can effectively increase the battery life.
Support multiple stacks, the total capacity of the batteries in parallel increases, and the voltage remains unchanged. However, since the discharge of each battery is not balanced during use, there is a voltage difference between the batteries, which may cause the battery to charge backwards. .(will lose part of the battery capacity)
ESP32 module currently does not support WiFi in 5G band, only 2.4G.
Confirm whether the TX/RX pin on the TTL side of the pin is correct, try to add two 120Ω terminal resistors at the beginning and end of the device line to reduce signal reflection interference
Click the link below to view the product comparison table
Rotate the lens to adjust the focal length within a certain range
FACE II BOTTOM NOT CORE2 COMPATIBLE
Use esptool to read the flash content of esp32 and export the bin file. Refer to the detailed operation
Restart the Arduino IDE, the computer uses the mobile AP mobile network to download.
Refer to the Github link below, use arduino-esp32fs-plugin for file upload
Check if the COM of the corresponding device is selected and if the M5Burner is the latest version
UIFlow users can switch the Label font to Unicode, Arduino users can use the Chinese font library provided in the M5GFX driver library
Confirm whether the SD card format is FAT32, and no partitions exist.
You can refer to the following link for other ESP32 users to share the case program
STAMP C3U enters program download mode operation: 1. Long press the center button (G9) of STAMP C3U when the power is off. 2. Connect to the computer, after the port is successfully identified, program burning.
By default, USB CDC is not enabled, the serial port output started by C3U will be output through the default pins (G20, G21) of UART0. If you want to output through USB, please use the IDE to output Its USB CDC option is enabled. (Arduino users can enable it through Tools->USB CDC on Boot-Enabled. For IDF users, please refer to the ESP IDF official documentation.)
Refer to the UIFlow documentation of the corresponding device to check whether the device has entered the USB programming mode.
Make sure that the NBIoT used is not locked. Frequent device replacement or after activating the IoT card, using traffic in different places may cause the card to be locked. If the above situation occurs, please contact the IoT card supplier. If you are using the IoT card matching M5, please contact M5 after-sales through e-commerce or email. (provide the ICCID of the IoT card)
Describe the problems encountered in detail. Screenshots of the programs involved or files can be added as attachments and sent to M5Stack's official after-sales email
M5Stack related resource links: Official Github