EasyLoader (beta)

Current Product Don't Have Test Firmware

Note: pls, use PC chrome/edge browser, if can't connect, refresh the webpage.

1. Click connect button

2. After connected successfully, pick a firmware

3. Click the burn button

4. After burning successfully, Unplug the device and restart.

0%

ATOM Matrix

SKU:C008-B

Tutorial

This tutorial will show you how to control ATOM devices through the UIFlow graphical programming platform
This tutorial will show you how to program and control ATOM devices through Arduino IDE
This tutorial will show you how to control ATOM devices through Micropython programming

Description

ATOM Matrix , which has a size of only 24 * 24mm, is the most compact development board in the M5Stack development kit series. It provides more GPIO pins and is very suitable for handy and miniature embedded device development. The main control adopts the ESP32-PICO-D4 chip, which comes integrated with Wi-Fi technologies and has 4MB of integrated SPI flash memory. The Atom board provides an Infra-Red LED along with the 5 * 5 RGB LED matrix on the panel, a built-in IMU sensor (MPU6886), and a HY2.0 interface. A general purpose programmable button is proved below the RGB Led matrix to enable users to add input support to their various projects. The on-board USB interface (Type-C) enables rapid program uploading and execution. One M2 screw hole is provided on the back for mounting the board.

Note: When using FastLED lib, the recommended brightness of RGB LED is 20. Please do not set it to a high brightness value to avoid damage to the LED and acrylic screen. (In ATOM lib, we have mapped its appropriate brightness range to 0~100)

Product Features

  • ESP32 PICO-based
  • Programmable button
  • 5 * 5 RGB LED matrix panel(WS2812C)
  • Built-in Infra-red LED
  • Built-in MPU6886 Inertial Sensor
  • Extendable Pins & Holes
  • Program Platform: Arduino UIFlow

Include

  • 1x ATOM Matrix

Applications

  • Internet of things terminal controller
  • IoT node
  • Wearable peripherals

Specification

Resources Parameter
ESP32 240MHz dual core, 600 DMIPS, 520KB SRAM, Wi-Fi
Flash 4MB
Power Input 5V @ 500mA
Port TypeC x 1, GROVE(I2C+I/0+UART) x 1
PIN Port G19, G21,G22,G23,G25, G33
RGB LED WS2812C 2020 x 25
MEMS MPU6886
IR Infrared transmission
Button Custom button x 1
Antenna 2.4G 3D Antenna
Operating Temperature 0°C to 60°C
Net weight 3g
Gross weight 14g
Product Size 242414mm
Package Size 434320mm
Case Material Plastic ( PC )

Driver Installation

Connect the device to the PC, open the device manager to install FTDI driver for the device. Take the win10 environment as an example, download the driver file that matches the operating system, unzip it, and install it through the device manager. (Note: In some system environments, the driver needs to be installed twice for the driver to take effect. The unrecognized device name is usually M5Stack or USB Serial. Windows recommends using the driver file to install directly in the device manager (custom Update), the executable file installation method may not work properly). Click here to download FTDI driver

EasyLoader

EasyLoader is a concise and fast program writer, which has a built-in case program related to the product. It can be burned to the main control by simple steps to perform a series of function verification.

Description:
Test whether the RGB LED and keys work normally by using the matrix screen text scroll display and key count function.

Download Windows Version Easyloader

Pin Map

Peripherals Pin
RGB Led G27
Btn G39
IR G12
SCL G21
SDA G25

Schematic

Learn

A modular Wi-Fi smart thermostat that doesn't need you to maintain any infrastructure: deploy it everywhere, integrate with everything.
Using M5StickC on RoverC and JoyC with M5Atom attached to display direction of the RoverC.
Simple MicroPython code for the ATOM 5 x 5 LED matrix and its built-in MPU6886 accelerometer. It works with the M5StickC + NeoFlash Hat.
A simple ESP-Now doorbell using an M5Stack Atom Matrix and Core2 controller.
A very simple game for the M5 ATOM. The unit must be tilted to the right or left depending if more red or more green pixels are displayed.
Wall clock shows time on two concentric NeoPixel LED rings. The inner ring shows the hours, the outer ring shows minutes and seconds
This is a project that uses Atom Matrix to customize shortcut keys, which is convenient for users to set key combinations
Here is a small thing that can help to use more electricity when it is produced by renewable sources.
A non-invasive solution for hot flashes during menopause using machine learning
We aim to realize a 1-axis attitude control module (inverted pendulum).
This year's Christmas, I decorated the tree with M5Stack devices.
I made the 1-axis attitude control module SHISEIGYO-1. It gets up without physical braking.

Example

Arduino IDE

  • To get the code, please click here
  • Before compiling the program, please configure the development board as M5StickC

UIFlow

  • Click here to view UIFlow example

Video

FAQ

Q1: How do I remove the speaker floor noise when the M5Core is on or running?

Execute the following statement in Setup() of the Arduino program

Q2: How does M5Core2 stack modules?

When M5Core2 is stacked with other M5 modules, you need to remove the battery base of Core2, which does not support module stacking.

Q3: A timeout error is displayed when uploading the program to the device

Reason and solution: The power supply current of the port is insufficient, which can cause the device to not enter the download mode normally. You can try to connect a capacitor (>0.1uF) between the RST pin and the GND pin, or when uploading the program, set the G0 Short-circuit to GND, so that G0 can be set to a low level state normally

Q4: How to solve the phenomenon of automatic signal triggering of M5Core button A

Add the header file #include <driver/adc.h> and the function adc_power_acquire(); in the Arduino program

Q5: M5 device battery life

The battery life of the controller is affected by various factors such as battery capacity, operating status, and load, so there is no fixed value. Reducing the load and adopting a sleep strategy can effectively increase the battery life.

Q6: Can multiple modules with batteries be stacked at the same time?

Support multiple stacks, the total capacity of the batteries in parallel increases, and the voltage remains unchanged. However, since the discharge of each battery is not balanced during use, there is a voltage difference between the batteries, which may cause the battery to charge backwards. .(will lose part of the battery capacity)

Q7: M5 master supports WiFi connection to 5G frequency band

ESP32 module currently does not support WiFi in 5G band, only 2.4G.

Q8: The RS485 device cannot communicate normally/data is garbled. Packet loss, etc.

Confirm whether the TX/RX pin on the TTL side of the pin is correct, try to add two 120Ω terminal resistors at the beginning and end of the device line to reduce signal reflection interference

Q9: The difference between different masters and camera products

Click the link below to view the product comparison table

Q10: M5 camera image blur, how to adjust the focal length

Rotate the lens to adjust the focal length within a certain range

Q11: The control RGB LED pin of FACE II BOTTOM conflicts with the I2S DOUT pin of CORE2

FACE II BOTTOM NOT CORE2 COMPATIBLE

Q1: How to read the programmed firmware?

Use esptool to read the flash content of esp32 and export the bin file. Refer to the detailed operation

Q2: Several solutions for esp32 board download failure in Arduino IDE board management

Restart the Arduino IDE, the computer uses the mobile AP mobile network to download.

Method 3: Download the resource package provided by M5Stack for direct installation, and extract the contents to the board management path of Arduino, such as (C:\Users\Sean\AppData\Local\Arduino15\packages), https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/arduino/packages/m5stack_v2.0.0.zip
Q3: Arduino SPIFFS file upload operation

Refer to the Github link below, use arduino-esp32fs-plugin for file upload

Q4: When M5Burner burns firmware, an error pop-up window or exception occurs

Check if the COM of the corresponding device is selected and if the M5Burner is the latest version

Q5: Does the M5 master device support multi-language display (Chinese, English, Japanese, Russian, etc.)?

UIFlow users can switch the Label font to Unicode, Arduino users can use the Chinese font library provided in the M5GFX driver library

Q6: The program cannot load the SD card normally

Confirm whether the SD card format is FAT32, and no partitions exist.

Q7: How to use Bluetooth, HTTP, SD, WebServer, FreeRTOS and other features in Arduino IDE

You can refer to the following link for other ESP32 users to share the case program

Q8: How to download programs for STAMP C3U

STAMP C3U enters program download mode operation: 1. Long press the center button (G9) of STAMP C3U when the power is off. 2. Connect to the computer, after the port is successfully identified, program burning.

Q9: How STAMP C3U defines UART0 output mode

By default, USB CDC is not enabled, the serial port output started by C3U will be output through the default pins (G20, G21) of UART0. If you want to output through USB, please use the IDE to output Its USB CDC option is enabled. (Arduino users can enable it through Tools->USB CDC on Boot-Enabled. For IDF users, please refer to the ESP IDF official documentation.)

Q10: Unable to connect to UIFlow Desktop IDE

Refer to the UIFlow documentation of the corresponding device to check whether the device has entered the USB programming mode.

Q11: NBIoT devices cannot connect to the network normally

Make sure that the NBIoT used is not locked. Frequent device replacement or after activating the IoT card, using traffic in different places may cause the card to be locked. If the above situation occurs, please contact the IoT card supplier. If you are using the IoT card matching M5, please contact M5 after-sales through e-commerce or email. (provide the ICCID of the IoT card)

COMMON

Q1: Consultation for after-sales problems of products

Describe the problems encountered in detail. Screenshots of the programs involved or files can be added as attachments and sent to M5Stack's official after-sales email

Q2: Code Resources, Cases, User Communication