COM.NB-IoT is a stackable multi-band NB-IoT wireless communication module with built-in SIM7020G communication module. The module supports PSM and eDRX low power consumption modes.
The COM.NB-IoT module has a wide coverage signal. Compared to GSM, NB-IoT has a strong gain, which also enables the product to have wireless communication capabilities in locations such as basements.
The module has a DC power input and can provide 5V-12V power supply through an external power supply. In order to facilitate the user to configure the pin, the DIP switch is used to set the pin. The SIM7020G module is the optimal solution for low latency, low power consumption, and low throughput applications. It is very suitable for IoT applications such as metering, remote control, asset tracking, remote monitoring, telemedicine, and ride sharing.
When used with the FIRE main control, due to the PSRAM pin conflict, please switch the DIP switch pins of the module base to TX(0/13), RX(5/15), and the device can use USB/ External DC is used for power supply.
When used with Core2 series main control, due to the different order of the base pin array, COM.X base pins TX(16), RX(17) correspond to the actual pins TX(14), RX of the Core2 main control (13) The equipment needs to use external DC for power supply.
Note: When using the CORE2 or CORE2-FOR-AWS main control to drive the module, please use the DC power input of the base and set the power mode to input mode (refer to the code below), otherwise it will not start normally //mbus_mode_t: //kMBusModeOutput: Use USB or battery power //kMBusModeInput: Use external power supply 5V, or DC interface M5.begin(true, true, true, false, kMBusModeInput); //Initialize Serial according to the actual connected pins Serial2.begin(115200, SERIAL_8N1, 13, 14);
The module base has a DC power input interface. Please strictly follow the input range (5-12V) to prevent damage to the module when using this interface to connect to the power supply. The internal power DIP switch can adjust the voltage level of the internal terminal VIN to adapt to different modules.
Support low power consumption mode
Strong signal access capability
Independent external power supply
AT command control
SIM card type: MicroSIM
Status signal: two LED indicators
External antenna: SMA antenna
Serial communication: UART 115200bps
Data transmission speed: Upload:150Kbps Download:126Kbps
Protol: TCP/UDP/HTTP/HTTPS/TLS/DTLS/DNS/ NTP/PING/LWM2M/COAP/MQTT/MQTTS
• Telstra*(on going)
• Deutsche Telekom
|Network protocol||TCP/UDP/HTTP/HTTPS/TLS/DTLS/DNS/ NTP/PING/LWM2M/COAP/MQTT/MQTTS|
|DC interface specifications||5.5mm|
The following content is for reference only.
|North America||B4 (1700), B12 (700), B66 (1700), B71 (600), B26 (850)|
|Asia Pacific||B1(2100), B3(1800), B5(850), B8(900), B18(850), B20(800), B26(850),B28(700)|
|Europe:||B3 (1800), B8 (900) , B20 (800)|
|Latin America||B2(1900), B3(1800), B5(850), B28(700)|
|Commonwealth of Independent States||B3 (1800), B8 (900), B20 (800)|
|Sub-Saharan Africa||B3(1800), B8(900)|
|Middle East, North Africa||B8(900), B20(800)|
EasyLoader is a concise and fast program writer, which has a built-in case program related to the product. It can be burned to the main control by simple steps to perform a series of function verification.
Check signal strength,Register to the network,5 and 13 of the DIP switch are set to ON.
To get complete code, please click here