EasyLoader (beta)

Current Product Don't Have Test Firmware

Note: pls, use PC chrome/edge browser, if can't connect, refresh the webpage.

1. Click connect button

2. After connected successfully, pick a firmware

3. Click the burn button

4. After burning successfully, Unplug the device and restart.

0%

PoECAM

SKU:U121

Description

PoECAM is an open source Fully programmable camera integrating PoE (Power Over Ethernet) . This item is ESP32 based webcam with W5500 embedded Ethernet controller plus 2M pixel image sensor OV2640. PoECAM equipped with a combination of 8MB PSRAM + 16MB Flash large memory. This teeny tiny with flexible power supply, you can get stable image by connecting the network cable in just 2 steps. It's wonderful for you to monitor warehouse, get auto image acquisition, etc.

  • Plug and Play:

    • One step to get the IP by connecting to the network cable, You can view the images from any device in the wireless LAN.
    • Image data acquisition due to it's own existing software
    • CameraTool'/UART image transfer with PC upper computer
  • Abundant features:

    • ESP32 embedded, reserved burning interface for developing
    • W5500 embedded Ethernet controller supports `TCP, UDP, IPv4, ICMP, ARP, IGMP and PPPoE protocols
    • Exporting image data in various formats /Tuning Image Parameters
  • Highly flexible:

    • Support PoE power supply Network cable & power supply 2 in 1, wiring simplified / Support 5V power supply
    • GROVE expansion interface
    • Camera fixed back clip for wall hanging

Product Features

  • Rich image processing API interface
  • PoE IEEE802.3 AF specification
  • Ethernet webcam
  • Built-in ESP32 MCU
  • Development platform:
    • UIFlow, Arduino, ESP-IDF
    • Software code / hardware open source

Include

  • 1x PoECAM
  • 1x Camera mount clip
  • 1x LEGO compatible clip

Applications

  • Warehouse monitoring
  • Timed filming

Specifications

Specifications Parameters
ESP32-D0WDQ6-V3 240MHz dual core, 600 DMIPS, 520KB SRAM
Flash 16MB
PSRAM 8MB
Image Sensor OV2640
Maximum Resolution 2MegaPixel
OV2640 supports the maximum image transmission rate YUV(422/420)/YCbCr422, 8-bit compressed data, RGB565/555, 8-/10-bit Raw RGB data
DFOV 65°
PoE specification PoE IEEE802.3 AF specification / maximum power 6W
Ethernet Controller W5500, built-in 32Kbytes buffer area, SPI interface
Support protocols TCP, UDP, IPv4, ICMP, ARP, IGMP and PPPoE protocols
Ethernet interface specifications RJ45
Basic Peripherals 1x programmable buttons, 2x work indicator lights
Net weight 38g
Gross weight 45g
Product size 64 * 24 * 18mm
Packing size 80 * 37 * 32mm

Notes:
1. The PoECAM download program requires an external ESP32 burner, you can click here to buy the official M5 ESP32-Downloader kit, which includes a small adapter board, and the connection will be even better Convenient
2. The factory firmware of PoECAM will automatically obtain the IP after connecting to the switch and start the web server. By viewing the serial port output of PoECAM, you can get the IP address and the image stream URL, and you can preview the image in real time by visiting the URL with a browser under the same local area network.

Pin mapping

OV2640 interface

接口 Camera Pin PoE CAM
SCCB Clock SIOC G12
SCCB Data SIOD G14
System Clock XCLK G27
Vertical Sync VSYNC G22
Horizontal Reference HREF G26
Pixel Clock PCLK G21
Pixel Data Bit 0 D0 G32
Pixel Data Bit 1 D1 G35
Pixel Data Bit 2 D2 G34
Pixel Data Bit 3 D3 G5
Pixel Data Bit 4 D4 G39
Pixel Data Bit 5 D5 G18
Pixel Data Bit 6 D6 G36
Pixel Data Bit 7 D7 G19
Camera Reset RESET G15
Camera Power Down PWDN -1
Power Supply 3.3V 3V3 3V3
Ground GND GND

W5500 interface

W5500 PoE CAM
MOSI G13
MISO G38
SCLK G23
CS G4

EXT.PORT

EXT.PORT PoE CAM
RX G25
TX G33
5V 5V
GND GND

Right button

Button PoE CAM
Signal G37

Blue LED

Blue LED PoE CAM
Signal G0

Schematic

Example

Arduino

PoECAM HTTP STREAM

Video

FAQ

Q1: How do I remove the speaker floor noise when the M5Core is on or running?

Execute the following statement in Setup() of the Arduino program

Q2: How does M5Core2 stack modules?

When M5Core2 is stacked with other M5 modules, you need to remove the battery base of Core2, which does not support module stacking.

Q3: A timeout error is displayed when uploading the program to the device

Reason and solution: The power supply current of the port is insufficient, which can cause the device to not enter the download mode normally. You can try to connect a capacitor (>0.1uF) between the RST pin and the GND pin, or when uploading the program, set the G0 Short-circuit to GND, so that G0 can be set to a low level state normally

Q4: How to solve the phenomenon of automatic signal triggering of M5Core button A

Add the header file #include <driver/adc.h> and the function adc_power_acquire(); in the Arduino program

Q5: M5 device battery life

The battery life of the controller is affected by various factors such as battery capacity, operating status, and load, so there is no fixed value. Reducing the load and adopting a sleep strategy can effectively increase the battery life.

Q6: Can multiple modules with batteries be stacked at the same time?

Support multiple stacks, the total capacity of the batteries in parallel increases, and the voltage remains unchanged. However, since the discharge of each battery is not balanced during use, there is a voltage difference between the batteries, which may cause the battery to charge backwards. .(will lose part of the battery capacity)

Q7: M5 master supports WiFi connection to 5G frequency band

ESP32 module currently does not support WiFi in 5G band, only 2.4G.

Q8: The RS485 device cannot communicate normally/data is garbled. Packet loss, etc.

Confirm whether the TX/RX pin on the TTL side of the pin is correct, try to add two 120Ω terminal resistors at the beginning and end of the device line to reduce signal reflection interference

Q9: The difference between different masters and camera products

Click the link below to view the product comparison table

Q10: M5 camera image blur, how to adjust the focal length

Rotate the lens to adjust the focal length within a certain range

Q1: How to read the programmed firmware?

Use esptool to read the flash content of esp32 and export the bin file. Refer to the detailed operation

Q2: Several solutions for esp32 board download failure in Arduino IDE board management

Restart the Arduino IDE, the computer uses the mobile AP mobile network to download.

Method 3: Download the resource package provided by M5Stack for direct installation, and extract the contents to the board management path of Arduino, such as (C:\Users\Sean\AppData\Local\Arduino15\packages), https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/arduino/packages/m5stack_v2.0.0.zip
Q3: Arduino SPIFFS file upload operation

Refer to the Github link below, use arduino-esp32fs-plugin for file upload

Q4: When M5Burner burns firmware, an error pop-up window or exception occurs

Check if the COM of the corresponding device is selected and if the M5Burner is the latest version

Q5: Does the M5 master device support multi-language display (Chinese, English, Japanese, Russian, etc.)?

UIFlow users can switch the Label font to Unicode, Arduino users can use the Chinese font library provided in the M5GFX driver library

Q6: The program cannot load the SD card normally

Confirm whether the SD card format is FAT32, and no partitions exist.

Q7: How to use Bluetooth, HTTP, SD, WebServer, FreeRTOS and other features in Arduino IDE

You can refer to the following link for other ESP32 users to share the case program

Q8: How to download programs for STAMP C3U

STAMP C3U enters program download mode operation: 1. Long press the center button (G9) of STAMP C3U when the power is off. 2. Connect to the computer, after the port is successfully identified, program burning.

Q9: How STAMP C3U defines UART0 output mode

By default, USB CDC is not enabled, the serial port output started by C3U will be output through the default pins (G20, G21) of UART0. If you want to output through USB, please use the IDE to output Its USB CDC option is enabled. (Arduino users can enable it through Tools->USB CDC on Boot-Enabled. For IDF users, please refer to the ESP IDF official documentation.)

Q10: Unable to connect to UIFlow Desktop IDE

Refer to the UIFlow documentation of the corresponding device to check whether the device has entered the USB programming mode.

COMMON

Q1: Consultation for after-sales problems of products

Describe the problems encountered in detail. Screenshots of the programs involved or files can be added as attachments and sent to M5Stack's official after-sales email

Q2: Code Resources, Cases, User Communication