Current Product Don't Have Test Firmware
Note: pls, use PC chrome/edge browser, if can't connect, refresh the webpage.
1. Click connect button
2. After connected successfully, pick a firmware
3. Click the burn button
4. After burning successfully, Unplug the device and restart.
ATOM DTU LoRaWAN470 is a LoRaWAN Programmable Data Transmission Unit (DTU) suitable for 470MHz frequency. The module adopts the ASR6501 scheme, which supports long-distance communication and has both ultra-low power consumption and high sensitivity. The module integrates the LoRaWAN protocol stack and adopts a serial communication interface (using AT command set for control). When used, it can be used as a collection node to access a large number of gateways for data collection and management. Integrate SMA external antenna interface to improve the communication quality and signal stability of the device. Unlike the DTU which generally only has the function of data transparent transmission, the ATOM DTU series adopts a more open architecture design. The controller ATOM LITE can modify the program at will according to the actual business. The whole machine reserves a variety of interfaces (RS485, I2C, custom interface) for user expansion, which is convenient for the rapid access of sensors and actuators. With its own guide rail clamping structure, it is perfectly embedded in various industrial control sites.
|Minimum receiving sensitivity||-137dBm (SF=12/BW=125KHz)|
|Maximum transmit power||+21dBm|
|Product Size||64 * 24 * 29mm|
|Package Size||91 * 42 * 24.5mm|
Before using UIFlow programming, you need to burn the UIFlow firmware for the ATOM master, click here to view the quick start tutorial .
Init LoRaWAN 470 DTU
Initialize the module
Config ABP mode device address app session key network session ket
Configure ABP mode to access the network
Get ABP config
Get network access information in ABP mode
Config OTAA mode device eui app eui app key
Configure OTAA mode to access the network
Get OTAA config
Get network access information in OTAA mode
Set frequency band mask channels
Set the frequency band mask channel
Config RX window param RX1 offset RX2 data rate BW125 RX2 freq(Hz)
Set the RX window parameters
Set class mode
Set the class mode
Set uplink downlink mode
Set up and down link mode
Check join status
Check the status of joining the network
Set join mode
Set the mode of access to the network
Join LoRaWAN network join auto join period (seconds) maximum number of attempts
Set the information of device access to the network
Set uplink app port (1 ~ 233)
Set the uplink application port (1 ~ 233)
Send data payload
Send data payload to the server
Check uplink data status
Check the status of uplink data
Check and receive downlink data
Check and receive downlink data
RS485 write a line
Write a line of data
RS485 write raw data create list with
Write raw data in list form
RS485 read all
Read all data of RS485
RS485 read characters
Read the number of characters of RS485
RS485 read line
Read the data of a line of RS485
Remain cache of RS485
Read coils slave address starting address coil qty
Read the data of the coils
Read discrete inputs slave address starting address input qty
Read the data of the discrete inputs
Read holding registers slave address starting address register qty signed
Read the data of the holding registers
Read input registers slave address starting address register qty signed
Read the data of the input registers
Write single coil slave address output address output value
Write data to a single coil
Write single register slave address register address register value signed
Write data to a single register
Write multiple coils slave address starting address output value
Write data to multiple coils
Write multiple register slave address starting address register value signed
Write data to multiple register
Use OTAA to access the network and send messages continuously.
Click here to download the case program
Execute the following statement in Setup() of the Arduino program
When M5Core2 is stacked with other M5 modules, you need to remove the battery base of Core2, which does not support module stacking.
Reason and solution: The power supply current of the port is insufficient, which can cause the device to not enter the download mode normally. You can try to connect a capacitor (>0.1uF) between the RST pin and the GND pin, or when uploading the program, set the G0 Short-circuit to GND, so that G0 can be set to a low level state normally
Add the header file #include <driver/adc.h> and the function adc_power_acquire(); in the Arduino program
The battery life of the controller is affected by various factors such as battery capacity, operating status, and load, so there is no fixed value. Reducing the load and adopting a sleep strategy can effectively increase the battery life.
Support multiple stacks, the total capacity of the batteries in parallel increases, and the voltage remains unchanged. However, since the discharge of each battery is not balanced during use, there is a voltage difference between the batteries, which may cause the battery to charge backwards. .(will lose part of the battery capacity)
ESP32 module currently does not support WiFi in 5G band, only 2.4G.
Confirm whether the TX/RX pin on the TTL side of the pin is correct, try to add two 120Ω terminal resistors at the beginning and end of the device line to reduce signal reflection interference
Click the link below to view the product comparison table
Rotate the lens to adjust the focal length within a certain range
FACE II BOTTOM NOT CORE2 COMPATIBLE
Use esptool to read the flash content of esp32 and export the bin file. Refer to the detailed operation
Restart the Arduino IDE, the computer uses the mobile AP mobile network to download.
Refer to the Github link below, use arduino-esp32fs-plugin for file upload
Check if the COM of the corresponding device is selected and if the M5Burner is the latest version
UIFlow users can switch the Label font to Unicode, Arduino users can use the Chinese font library provided in the M5GFX driver library
Confirm whether the SD card format is FAT32, and no partitions exist.
You can refer to the following link for other ESP32 users to share the case program
STAMP C3U enters program download mode operation: 1. Long press the center button (G9) of STAMP C3U when the power is off. 2. Connect to the computer, after the port is successfully identified, program burning.
By default, USB CDC is not enabled, the serial port output started by C3U will be output through the default pins (G20, G21) of UART0. If you want to output through USB, please use the IDE to output Its USB CDC option is enabled. (Arduino users can enable it through Tools->USB CDC on Boot-Enabled. For IDF users, please refer to the ESP IDF official documentation.)
Refer to the UIFlow documentation of the corresponding device to check whether the device has entered the USB programming mode.
Make sure that the NBIoT used is not locked. Frequent device replacement or after activating the IoT card, using traffic in different places may cause the card to be locked. If the above situation occurs, please contact the IoT card supplier. If you are using the IoT card matching M5, please contact M5 after-sales through e-commerce or email. (provide the ICCID of the IoT card)
Describe the problems encountered in detail. Screenshots of the programs involved or files can be added as attachments and sent to M5Stack's official after-sales email